Astro Tungsten Carbide Floppy Rod 999A1 Welding Electrode

Astro Tungsten Carbide Floppy Rod 999A1 Welding Electrode

In our unique, flexible Astro 999A1 consumable, crushed or spherical carbides surround a small diameter nickel core wire and are set in a high grade nickel alloy matrix and binder.  The dense, wear resistant properties of the finished surfacing are assured, by maintaining both the ratio and combination of carbide sizes throughout the length of the rod.

Astro’s tungsten carbide 999-A1 can be used under the most severe conditions in many industries to achieve longer life against abrasion, less down time and to serve as a protective surface which can be rebuilt again and again when necessary.

Applications:

• Oil industry - On stabilisers, drill strings, bits and finishing tools
• Dredging - On cutter teeth, dragging teeth and pump castings
• Cement and brick- On augers, extruder and feed screws, deflection cones, pump rings and liners
• ALLOY AND STEEL FOUNDRIES - On sand and coal mixer paddles, guides and raking equipment
• Paper - On mixers, compression screws, pulverisers and shredders
• Mining and Power- Between coal crusher teeth, on rotating bucket teeth, and pulverised fuel system
• Clay and Ceramics - On wetting and mixing units, grinding cylinder scrapers, rakes and crusher teeth
• Plastics and Rubber - On mixer/extrution screws and liners, rotors and spares

Benefits:

• Reduced distortion and oxidation of base metal

• Dense distribution of carbide particles

• Continuous solid, but flexible

• Corrosion resistant matrix

• Faster coverage rates

• Easy repair

Oxy Welding Procedures:

• As with all surfacing products, the removal of any scale, rust or oxidation from the base material by machining or grinding is essential.
• Use a nozzle at least one size larger than usual for fusion welding the thickness of metal.
• Use a flame with an excess of acetylene.
• Do NOT melt the base metal, it should only ‘sweat’.
• Do NOT stir the molten pool, otherwise the hard particles will sink and the surface will become too soft.
• The thickness of each layer should not exceed 3mm. (maximum 2 layers, 6mm).
• As with all surfacing products, the removal of any scale, rust or oxidation from the base material by machining or grinding is essential.
• Use a nozzle at least one size larger than usual for fusion welding the thickness of metal.
• Use a flame with an excess of acetylene.
• Do NOT melt the base metal, it should only ‘sweat’.
• Do NOT stir the molten pool, otherwise the hard particles will sink and the surface will become too soft.
• The thickness of each layer should not exceed 3mm. (maximum 2 layers, 6mm).

For more information please call or use the IndustrySearch Email form for a fast and direct reply.

Read more...

To contact Astro Alloys about Astro Tungsten Carbide Floppy Rod 999A1 Welding Electrode use Get a quote.

In our unique, flexible Astro 999A1 consumable, crushed or spherical carbides surround a small diameter nickel core wire and are set in a high grade nickel alloy matrix and binder.  The dense, wear resistant properties of the finished surfacing are assured, by maintaining both the ratio and combination of carbide sizes throughout the length of the rod.

Astro’s tungsten carbide 999-A1 can be used under the most severe conditions in many industries to achieve longer life against abrasion, less down time and to serve as a protective surface which can be rebuilt again and again when necessary.

Applications:

• Oil industry - On stabilisers, drill strings, bits and finishing tools
• Dredging - On cutter teeth, dragging teeth and pump castings
• Cement and brick- On augers, extruder and feed screws, deflection cones, pump rings and liners
• ALLOY AND STEEL FOUNDRIES - On sand and coal mixer paddles, guides and raking equipment
• Paper - On mixers, compression screws, pulverisers and shredders
• Mining and Power- Between coal crusher teeth, on rotating bucket teeth, and pulverised fuel system
• Clay and Ceramics - On wetting and mixing units, grinding cylinder scrapers, rakes and crusher teeth
• Plastics and Rubber - On mixer/extrution screws and liners, rotors and spares

Benefits:

• Reduced distortion and oxidation of base metal

• Dense distribution of carbide particles

• Continuous solid, but flexible

• Corrosion resistant matrix

• Faster coverage rates

• Easy repair

Oxy Welding Procedures:

• As with all surfacing products, the removal of any scale, rust or oxidation from the base material by machining or grinding is essential.
• Use a nozzle at least one size larger than usual for fusion welding the thickness of metal.
• Use a flame with an excess of acetylene.
• Do NOT melt the base metal, it should only ‘sweat’.
• Do NOT stir the molten pool, otherwise the hard particles will sink and the surface will become too soft.
• The thickness of each layer should not exceed 3mm. (maximum 2 layers, 6mm).
• As with all surfacing products, the removal of any scale, rust or oxidation from the base material by machining or grinding is essential.
• Use a nozzle at least one size larger than usual for fusion welding the thickness of metal.
• Use a flame with an excess of acetylene.
• Do NOT melt the base metal, it should only ‘sweat’.
• Do NOT stir the molten pool, otherwise the hard particles will sink and the surface will become too soft.
• The thickness of each layer should not exceed 3mm. (maximum 2 layers, 6mm).

For more information please call or use the IndustrySearch Email form for a fast and direct reply.

Read less...

To contact Astro Alloys about Astro Tungsten Carbide Floppy Rod 999A1 Welding Electrode use Get a quote.