Waterworks - Bench Top Filtered Water Cooler | SD5C Get latest price

Bench Top Filtered Water Cooler | SD5C

In Stock

Fast flow taps and high clearance recessed alcove make it easy to draw water and fill water bottles or jugs. There is also a Free Filter Kit. The filter can be connected to the back of the unit or mounted remotely.

CABINET:

Top and front panels are moulded of UV treated ABS and side panels are zinc coated steel sheets covered in electrostatically applied high polymer polyester resin.

COLOUR:

High gloss cloud white available as standard.

DRIP TRAY:

Concealed lift-out design of a high impact durable plastic. Removable for sanitation, it incorporates an anti-splash grid which diverts drain water into the drip tray.

TAPS:

High impact polypropylene lever type. Fast flow and easy to operate. They’re assembled directly onto the reservoir and are fully recessed for added protection. Taps are 177mm above the drain grid allowing ample room for filling kettles and other tall objects. Hot tap has safety influence.

TOP:

One piece heat resistant plastic. This rust-proof top provides a flat surface to hold small coffee servers and trays.

FUNCTION STATUS DISPLAY:

Waterworks unique design. This exclusive device illuminates a red green signal indicating the Power/Hot/Cold position of the dispenser.

COOLING RESERVIOR:

Constructed of polypropylene plastic, approximately 12 litres in capacity. The reservoir features large radius corners to facilitate cleaning. The integrated zoned waterway and baffle system prevents ice rings from restricting chilled water flow. Cold water capacity below the baffle is 4.2 litres. Water above the baffle stays at or about room temperature.

AIR FILTER:

Located on the float assembly for easy access. The air filter contains a replaceable filter disc with a one micron membrane media.

FLOAT ASSEMBLY:

One stage polyethylene float valve system incorporates a primary float valve which maintains the water level in the reservoir and shuts off when full. The system is designed to operate on an incoming water pressure range of 140-700kPa and a pressure limiting valve should be fitted in situations where the mains pressure may fluctuate to greater than 700kpa.

REFRIGER ATION SYSTEM:

Ozone friendly HFC-134a refrigerant. Flow is controlled by capillary tube which has no moving parts. Condenser is air cooled static type for silent running. No fan assembly is required. Compressor is hermetically sealed, permanently lubricated and protected against motor overload.

ELECTRICAL:

240 Volts 50Hz single phase. A 1.5 metre house cable and 3 pin plug is supplied. Full load current is 1.5 amps.

POWER CONSUMPTION:

D5C : 0.25kwh/day & 7.5kwh/month D5CH : 1.6kwh/day 48 kwh/month

PERFORMANCE:

Tap 1 Outlet water 9DC approx Tap 2 Outlet water 18DC approx Hot Tap Outlet water 88DC approx

SHIPPING WEIGHT:

D5C: 20kg D5CH: 22kg

DIMENSIONS:

SD5C: 15kgs SD5CH: 17kg

D5C/D5CH: 310mmW x 310mmD x 1040mmH SD5C/SD5CH: 310mmW x 310mmD x 630mmH

WARRANTY:

The entire range of Waterworks D5 Series water coolers
are covered by a 12 Month Comprehensive Warranty (copy available on request). The warranty provides comprehensive parts and labour coverage, for the period of 12 months from the date of original sale.

Read more...

To contact Water Cooler Superstore about Waterworks Bench Top Filtered Water Cooler | SD5C use Get a quote.

Fast flow taps and high clearance recessed alcove make it easy to draw water and fill water bottles or jugs. There is also a Free Filter Kit. The filter can be connected to the back of the unit or mounted remotely.

CABINET:

Top and front panels are moulded of UV treated ABS and side panels are zinc coated steel sheets covered in electrostatically applied high polymer polyester resin.

COLOUR:

High gloss cloud white available as standard.

DRIP TRAY:

Concealed lift-out design of a high impact durable plastic. Removable for sanitation, it incorporates an anti-splash grid which diverts drain water into the drip tray.

TAPS:

High impact polypropylene lever type. Fast flow and easy to operate. They’re assembled directly onto the reservoir and are fully recessed for added protection. Taps are 177mm above the drain grid allowing ample room for filling kettles and other tall objects. Hot tap has safety influence.

TOP:

One piece heat resistant plastic. This rust-proof top provides a flat surface to hold small coffee servers and trays.

FUNCTION STATUS DISPLAY:

Waterworks unique design. This exclusive device illuminates a red green signal indicating the Power/Hot/Cold position of the dispenser.

COOLING RESERVIOR:

Constructed of polypropylene plastic, approximately 12 litres in capacity. The reservoir features large radius corners to facilitate cleaning. The integrated zoned waterway and baffle system prevents ice rings from restricting chilled water flow. Cold water capacity below the baffle is 4.2 litres. Water above the baffle stays at or about room temperature.

AIR FILTER:

Located on the float assembly for easy access. The air filter contains a replaceable filter disc with a one micron membrane media.

FLOAT ASSEMBLY:

One stage polyethylene float valve system incorporates a primary float valve which maintains the water level in the reservoir and shuts off when full. The system is designed to operate on an incoming water pressure range of 140-700kPa and a pressure limiting valve should be fitted in situations where the mains pressure may fluctuate to greater than 700kpa.

REFRIGER ATION SYSTEM:

Ozone friendly HFC-134a refrigerant. Flow is controlled by capillary tube which has no moving parts. Condenser is air cooled static type for silent running. No fan assembly is required. Compressor is hermetically sealed, permanently lubricated and protected against motor overload.

ELECTRICAL:

240 Volts 50Hz single phase. A 1.5 metre house cable and 3 pin plug is supplied. Full load current is 1.5 amps.

POWER CONSUMPTION:

D5C : 0.25kwh/day & 7.5kwh/month D5CH : 1.6kwh/day 48 kwh/month

PERFORMANCE:

Tap 1 Outlet water 9DC approx Tap 2 Outlet water 18DC approx Hot Tap Outlet water 88DC approx

SHIPPING WEIGHT:

D5C: 20kg D5CH: 22kg

DIMENSIONS:

SD5C: 15kgs SD5CH: 17kg

D5C/D5CH: 310mmW x 310mmD x 1040mmH SD5C/SD5CH: 310mmW x 310mmD x 630mmH

WARRANTY:

The entire range of Waterworks D5 Series water coolers
are covered by a 12 Month Comprehensive Warranty (copy available on request). The warranty provides comprehensive parts and labour coverage, for the period of 12 months from the date of original sale.

Read less...

To contact Water Cooler Superstore about Waterworks Bench Top Filtered Water Cooler | SD5C use Get a quote.