Signal Level Filter | DDIN/DIN Rail Protection

Signal Level Filter | DDIN/DIN Rail Protection

This module addresses over voltage transients with gas tubes and silicon avalanche components. In addition, sneak currents are mitigated with resettable fuses (PTC's). The PTC's increase resistance several orders of magnitude when overcurrents exceed safe levels. A normal state resumes when over currents are removed. The ability to self restore in this manner significantly increases suppressor performance and survivability.

The DDIN Series mounts onto a standard 35mm industrial din rail. There are two "Field Side" and two "Electronics Side" screw terminals. Two electrically tied ground terminals are provided for grounding the DDIN Series unit to Building Approved Ground.

Dimensions: 60mm x 75mm x 12.5mm

 

Specifications
Part Number	Max Peak Signal Voltage	Nominal Breakdown Voltage	Max Let-Thru Voltage 10 x 700µs @ 400Amps	Surge Current 10 x 1000µs (Occurrences)	Peak Current 8 x 20µs Waveform	Typ Cap (pf)	Max Cont. Current (ma)	Nom. Series Resistance
DDIN 008	6	8	15	>100	10KA	1500	150	5 Ohms
DDIN 015	12	15	20	>100	10KA	1500	150	5 Ohms
DDIN 232	15	22	30	>100	10KA	1500	150	5 Ohms
DDIN 030	24	30	35	>100	10KA	1500	150	5 Ohms
DDIN 036	30	36	45	>100	10KA	1500	150	5 Ohms
DDIN 043	35	43	55	>100	10KA	1500	150	5 Ohms
DDIN 050	43	50	72	>100	10KA	800	150	5 Ohms
DDIN 060	52	60	80	>100	10KA	600	150	5 Ohms
DDIN 130RMS**	170	200	350	>10	8KA	1000	N/A	5 Ohms

 

**Warning!! For Discrete Signal Use Only. Do not use DDIN-130RMS on 240VAC Power Lines. This unit is a Non-Hybrid, MOV design, rated above: (5A operational) current and can withstand greater than 8 occurrences of a 10kA 8 x 20µs waveform, and greater than 1000 occurrences of a 200A 10 x 1000µs waveform. 5 blank numbering tabs and 2 ground tabs are provided with each DDIN.

 

Read more...

To contact Dyne Industries about Signal Level Filter | DDIN/DIN Rail Protection use Get a quote.

This module addresses over voltage transients with gas tubes and silicon avalanche components. In addition, sneak currents are mitigated with resettable fuses (PTC's). The PTC's increase resistance several orders of magnitude when overcurrents exceed safe levels. A normal state resumes when over currents are removed. The ability to self restore in this manner significantly increases suppressor performance and survivability.

The DDIN Series mounts onto a standard 35mm industrial din rail. There are two "Field Side" and two "Electronics Side" screw terminals. Two electrically tied ground terminals are provided for grounding the DDIN Series unit to Building Approved Ground.

Dimensions: 60mm x 75mm x 12.5mm

 

Specifications
Part Number	Max Peak Signal Voltage	Nominal Breakdown Voltage	Max Let-Thru Voltage 10 x 700µs @ 400Amps	Surge Current 10 x 1000µs (Occurrences)	Peak Current 8 x 20µs Waveform	Typ Cap (pf)	Max Cont. Current (ma)	Nom. Series Resistance
DDIN 008	6	8	15	>100	10KA	1500	150	5 Ohms
DDIN 015	12	15	20	>100	10KA	1500	150	5 Ohms
DDIN 232	15	22	30	>100	10KA	1500	150	5 Ohms
DDIN 030	24	30	35	>100	10KA	1500	150	5 Ohms
DDIN 036	30	36	45	>100	10KA	1500	150	5 Ohms
DDIN 043	35	43	55	>100	10KA	1500	150	5 Ohms
DDIN 050	43	50	72	>100	10KA	800	150	5 Ohms
DDIN 060	52	60	80	>100	10KA	600	150	5 Ohms
DDIN 130RMS**	170	200	350	>10	8KA	1000	N/A	5 Ohms

 

**Warning!! For Discrete Signal Use Only. Do not use DDIN-130RMS on 240VAC Power Lines. This unit is a Non-Hybrid, MOV design, rated above: (5A operational) current and can withstand greater than 8 occurrences of a 10kA 8 x 20µs waveform, and greater than 1000 occurrences of a 200A 10 x 1000µs waveform. 5 blank numbering tabs and 2 ground tabs are provided with each DDIN.

 

Read less...

To contact Dyne Industries about Signal Level Filter | DDIN/DIN Rail Protection use Get a quote.