Electrical Test and Tag | Materials Handling Equipment

Electrical Test and Tag | Materials Handling Equipment

AS3760:2003 Safety inspection and testing of low voltage single phase and poly-phase (e.g. nominal 240v and 415v) electrical equipment connected to the electrical supply by a flexible cord.

ARK testing can test and tag all portable electrical appliances to 3 phase machinery

ARK testing only uses the top of the line, up-to-date testing equipment, the AlphaPAT SupaPAT and Metrel SmarTEC.

Occupational health and safety section AS/NZS 3760: 2003 require businesses to have electrical equipment appliances tested and tagged for safety compliance.

Regular Checking of Electrical Equipment

The Victorian Energy Safety Regulator, Energy Safe Victoria (ESV), has received a number of incident reports from construction sites and other locations around Victoria where workers have suffered an electrical shock or burn while using faulty electrical tools and equipment that had a current test tag attached.

Equipment with a current test tag is not guaranteed to be safe for the remainder of the test cycle. ESV has seen many instances where the supply cord has been nicked, or the casing broken. exposing live parts to possible contact and electric shock on equipment with a current test tag fitted.

The following safety precautions should be adopted to prevent possible electrocution.

Always

• Test and tag electrical leads, tools and equipment regularly.
• Visually inspect electrical leads, tools and equipment for damage before each use.
• Use safety switches (also called RCDs) when using electrical tools & equipment.
• Use competent people to repair damaged electrical leads tools and equipment

Never

• Use damaged electrical leads, tools and equipment.
• Use electrical leads. tools and equipment in damp or wet conditions unless they are specially designed for use in those conditions.
• Place electrical leads in areas where they may be damaged (e.g. on the ground, through doorways and over sharp edges).
• Overload electrical circuits.
• Use modified electrical tools and equipment.

Testing of Electrical Equipment

Portable electrical equipment including flexible electrical cords needs to be regularly inspected for wear and mechanical damage and periodically tested for earth continuity and insulation resistance.

Procedures for testing of electrical leads, tools and equipment and the frequency of these tests can be found in:

• Joint Australian and New Zealand Standard AS/NZS 3760 In-service safety inspection and testing of electrical equipment; and
• Joint Australian and New Zealand Standard AS/NZS 3012 Electrical installations - construction and demolition sites

Read more...

To contact ARK Testing about Electrical Test and Tag | Materials Handling Equipment use Get A Quote.

AS3760:2003 Safety inspection and testing of low voltage single phase and poly-phase (e.g. nominal 240v and 415v) electrical equipment connected to the electrical supply by a flexible cord.

ARK testing can test and tag all portable electrical appliances to 3 phase machinery

ARK testing only uses the top of the line, up-to-date testing equipment, the AlphaPAT SupaPAT and Metrel SmarTEC.

Occupational health and safety section AS/NZS 3760: 2003 require businesses to have electrical equipment appliances tested and tagged for safety compliance.

Regular Checking of Electrical Equipment

The Victorian Energy Safety Regulator, Energy Safe Victoria (ESV), has received a number of incident reports from construction sites and other locations around Victoria where workers have suffered an electrical shock or burn while using faulty electrical tools and equipment that had a current test tag attached.

Equipment with a current test tag is not guaranteed to be safe for the remainder of the test cycle. ESV has seen many instances where the supply cord has been nicked, or the casing broken. exposing live parts to possible contact and electric shock on equipment with a current test tag fitted.

The following safety precautions should be adopted to prevent possible electrocution.

Always

• Test and tag electrical leads, tools and equipment regularly.
• Visually inspect electrical leads, tools and equipment for damage before each use.
• Use safety switches (also called RCDs) when using electrical tools & equipment.
• Use competent people to repair damaged electrical leads tools and equipment

Never

• Use damaged electrical leads, tools and equipment.
• Use electrical leads. tools and equipment in damp or wet conditions unless they are specially designed for use in those conditions.
• Place electrical leads in areas where they may be damaged (e.g. on the ground, through doorways and over sharp edges).
• Overload electrical circuits.
• Use modified electrical tools and equipment.

Testing of Electrical Equipment

Portable electrical equipment including flexible electrical cords needs to be regularly inspected for wear and mechanical damage and periodically tested for earth continuity and insulation resistance.

Procedures for testing of electrical leads, tools and equipment and the frequency of these tests can be found in:

• Joint Australian and New Zealand Standard AS/NZS 3760 In-service safety inspection and testing of electrical equipment; and
• Joint Australian and New Zealand Standard AS/NZS 3012 Electrical installations - construction and demolition sites

Read less...

To contact ARK Testing about Electrical Test and Tag | Materials Handling Equipment use Get A Quote.