Submersible Level Sensor & Transmitter Suppliers in Sydney & Melbourne & Brisbane

A submersible level sensor is a type of sensor that is designed to measure liquid levels in a submersible environment. These sensors are typically used in applications where the sensor needs to be submerged in the liquid being measured, such as in tanks, wells, and other liquid storage vessels. The sensor works by measuring the pressure of the liquid above it, and converting that pressure into a measure of the liquid level. Submersible level sensors can be used in a variety of industries, including water and wastewater treatment, agriculture, and oil and gas. They are typically made of materials that are resistant to corrosion and other environmental factors, such as stainless steel or plastic, and may be designed for specific types of liquids, such as oil or water.

A submersible level sensor is a device used to measure the level of liquids in tanks, wells, and other containers. There are several types of submersible level sensors available in Australia, including:

• Hydrostatic: These sensors use the principle of hydrostatic pressure to measure the liquid level in a tank. They consist of a pressure transducer and a diaphragm that is exposed to the liquid. Hydrostatic sensors are commonly used in wastewater treatment plants and municipal water systems.
• Ultrasonic: These sensors use ultrasonic waves to measure the distance between the sensor and the liquid surface. They are non-contact sensors and are suitable for use in tanks with corrosive or hazardous liquids.
• Capacitive: These sensors use the principle of capacitance to measure the liquid level. They consist of two electrodes separated by a dielectric material, and the capacitance between the electrodes changes as the liquid level changes. Capacitive sensors are commonly used in food and beverage industries.
• Optical: These sensors use light to measure the liquid level. They consist of an emitter and a receiver, and the liquid level is determined by the amount of light that is reflected back to the receiver. Optical sensors are commonly used in chemical and pharmaceutical industries.
• Radar: These sensors use radar waves to measure the liquid level. They emit high-frequency radio waves that reflect off the liquid surface and are detected by the sensor. Radar sensors are commonly used in oil and gas industries.

In conclusion, the choice of submersible level sensor depends on the application and the type of liquid being measured. Each type has its own advantages and disadvantages, and it is important to choose the right sensor for the job.

Is a device used to measure the level of liquids in tanks, reservoirs, and other containers. When purchasing a submersible level sensor in Australia, here are some key features to consider:

• Pressure range: The pressure range of the sensor must be suitable for the application. A sensor with a higher pressure range is needed for deeper tanks or containers.
• Accuracy: The accuracy of the sensor is critical, and it must be able to provide accurate readings even in harsh environments.
• Material: The material of the sensor must be suitable for the liquid being measured. Stainless steel sensors are common, but other materials such as plastic or titanium may be needed for corrosive liquids.
• Cable length: The cable length must be long enough to reach the top of the container being measured.
• Output signal: The output signal of the sensor must be compatible with the data logger or controller being used.
• Installation: The sensor must be easy to install and maintain, with features such as a removable cable or a quick connect fitting.
• Temperature range: The sensor must be able to operate in the temperature range of the liquid being measured.

Cost: The cost of the sensor must be considered, as well as any ongoing maintenance or calibration costs.

S typically have a measurement range of up to 1000 feet or 300 meters, depending on the model and manufacturer. However, some sensors may have a smaller or larger range depending on their design and intended use. It is important to consult the manufacturer's specifications to determine the measurement range of a specific submersible level sensor.

Submersible level sensors are highly accurate and reliable instruments that can provide accurate measurements of liquid levels in various applications. The accuracy level of submersible level sensors typically ranges from 0.25% to 0.5% of the full scale of the sensor. This means that if the full scale of the sensor is 10 feet, the accuracy level of the sensor would be within 0.025 to 0.05 feet.

However, the accuracy level of submersible level sensors can be affected by various factors such as the temperature, pressure, and viscosity of the liquid being measured, as well as the installation and calibration of the sensor. Therefore, it is important to choose the right type of submersible level sensor for the specific application and to ensure proper installation and calibration to ensure accurate measurements.

Installation of Submersible Level Sensors require a few steps:

• Determine the location of the sensor: The sensor should be installed at the desired location in the tank or well.
• Prepare the mounting surface: The surface where the sensor will be mounted should be cleaned and free of any debris.
• Install the sensor: The sensor should be carefully lowered into the tank or well, making sure it is securely mounted in place.
• Connect the wiring: The wiring should be connected to the appropriate terminals on the sensor and then routed to the control panel.
• Test the sensor: Once the sensor is installed and wired, it should be tested to ensure it is functioning properly.

Overall, the installation process should be performed by a qualified technician or installer with experience in working with submersible level sensors.

S are commonly used in water and wastewater applications to measure the level of fluids. Proper maintenance is essential to ensure the accuracy and reliability of the sensor. Some maintenance tasks that are required for submersible level sensors include:

• Regular cleaning: Submersible level sensors can accumulate sediment and other debris over time, which can affect their accuracy. Regular cleaning is necessary to remove any buildup and maintain the sensor's performance.
• Calibration: Submersible level sensors may require calibration over time to ensure accurate readings. This can be done by comparing the sensor's readings with a calibrated reference measurement.
• Inspection: Regular inspection of the sensor and its installation can help identify any issues that may affect performance. This includes checking for damage to the sensor and its wiring, as well as ensuring that the sensor is properly installed and secured.
• Replacing worn components: Over time, components such as the sensor's diaphragm or seals may become worn and need to be replaced. Regular maintenance can help identify these issues before they affect the sensor's performance.

Overall, regular maintenance is essential to ensure the accuracy and reliability of submersible level sensors in water and wastewater applications. By following these maintenance tasks, operators can ensure that their sensors continue to provide accurate and reliable level measurements.

Submersible Level Sensors are designed to withstand harsh environments and can last for many years with proper maintenance. The lifespan of a submersible level sensor depends on various factors such as the quality of the sensor, the conditions of the application, and the frequency of maintenance. On average, submersible level sensors can last up to 10 years or more. However, some sensors have been known to last up to 20 years or more with proper care and maintenance. It is important to regularly check and clean the sensor to ensure it is functioning correctly and to replace any damaged or worn parts as needed.

The cost of submersible level sensors in Australia can vary depending on the brand, type, and features. Generally, prices range from $100 to $1000 or more. Some factors that can affect the cost include the sensing range, accuracy, construction materials, and output options. It is important to compare different options and consider the specific needs of the application when selecting a submersible level sensor.

Warranty periods vary depending on the manufacturer and model of the sensor. Some manufacturers offer a one-year warranty, while others offer up to a five-year warranty. It is important to check with the manufacturer or seller for specific warranty information before purchasing a submersible level sensor. Additionally, warranties may have certain limitations or exclusions, so it is important to review the warranty details carefully.