Bitron treatments in ALL your mechanical equipment

Supplier: Bi-tron Lubrication
29 May, 2020

Bitron treatments in ALL your mechanical equipment

The Commercial machinery operators, have now proven, that over 20 years of ADDING ALL the Bitron Treatments to ALL types of their mechanical equipment; that all their machinery,  treated with these amazing, genuine, original Bitron Treatments will operate efficiently for a life span, of MORE than TEN times, longer,  than expected, with almost zero maintenance costs, and almost zero fuel system servicing costs and winning the benefits of many thousands of dollars saved,  from a great reduction in fuel consumption,   There's literately many thousands of dollars to be saved in the operation of mechanical equipment, with Bitron Treatments added.  Some of my long time Bitron customers tell me that they find it very much Less Expensive to burn diesel with Bitron added,  than to burn diesel straight, without Bitron added.  Same as for using Petrol.

Many more operators should take up the opportunity to try these amazing Bitron treatments.

 

Application: As an additive package to motor oil and fuel in 1,800 Horse Power diesel engine driving 1000 KVA CUMMINS electrical generator: anti-wear protection and reduction in fuel and oil consumption during normal operation.

User: Asphalt Quarry

The above 1000 KVA Cummins Generator driven by 1,800 horse power engine was in service for more than 30,000 hours. According to the manufacturer’s instructions, oil and oil-filters had to be replaced every 250 hours. Bi-Tron Engine Treatment was added after the generator was in service for about 5,000 hours. Within a very short time of using Bi-Tron Engine Treatment and Bi-Tron Fuel Conditioner an average of
10% reduction in fuel consumption was recorded. Based on used oil analysis the oil change intervals were extended to every 1,000 hours and then to every 1,500 hours. Typically, this type of engine is overhauled after 17,000 hours in operation.

In this specific case the engine was taken apart after 30,000 hours not because it had to be overhauled but because of penetration of water into its oil system. In spite of the water, there was no indication whatsoever that the engine was deteriorating in performance. Nevertheless, after 100 hours in operation with water presence in the oil system, the general manager of the quarry decided to take the engine apart. “I have seen too many times what presence of water in the oil system can do to an engine, I don’t want to stretch my luck.” The general manager of the quarry was very impressed when he was told by the head mechanic in the repair shop that the engine parts looked like new and that he thought that there must had been a mistake in the paperwork, because the condition of the engine parts didn’t have any indication whatsoever that the engine was in operation for 30,000 hours or water penetrated the oil system. The engine was put together without replacing or machining any parts. According to our most conservative estimate, over 30,000 hours that the generator was in operation, the user saved at least $150,000 on repairs, fuel and oil consumption. The user spent only $7,690 on Bi-Tron products, a return of approximately $20 on each dollar invested in Bi-Tron.

 

  • All the liners were micro-measured. There was no wear whatsoever, all the dimensions were within the manufacture’s specs of a new engine.
  • In all the liners, you could see distinct traces of the cross-honing pattern of the original bore and the liner surfaces looked polished and shiny.
  • All the pistons had piston-skirts and piston rings completely clean of any build-up. The rings looked like new and did not have any wear whatsoever (very unusual phenomenon, taking into consideration that the engine was in service for 30,000 hours and had water in its oil system for more than 100 hours.)
  • After 30,000 hours in operation and 100 hours in the presence of water, no piston pins had any traces of wear, looked shiny and new.
  • Usually, after 17,000 hours in operation there are extensive clearances between the piston pin and piston-pin bearing. In this case, there were no clearances at all in spite of the fact that the engine was in service for 30,000 hours and had water in its oil system for 100 hours while in operation.
  • At the same time, the repair shop had another similar engine that was in operation for 16,000 hours (that did not use Bi-Tron) and broke down  because of penetration of water into its oil system.

Our customer’s engine with Bi-Tron, was in operation 30,000 hours, and also was taken apart because of penetration of water into its oil system, didn’t break down, and there was no damage whatsoever to its parts. In addition, there were no traces of wear on all the engine parts.

Application: As an additive to motor oil in diesel engine in 800 KVA CUMMINS electrical generator: anti-wear protection during regular operation. User: Quarry: Asphalt production facility (overseas)

(Letter written by the General Manager of the asphalt production facility)

 

"Here is one example of "used oil analysis" test results from "Institute of Failure Analysis" based on which we decided to use Bi-Tron Engine Treatment in our diesel generators and extend their oil change intervals.

Test No.

Generator-hours

Oil-hours

397 9,900 1,050  640 11,150 1,250

 

Motor oil used in the generator was 15W-40 with 10% Bi-Tron Engine Treatment. Spectrometric analysis of concentration of wear-metals and physical characteristics of the used oil have been tested with the following results:

 

Concentration of metals, ppm (parts per million) and the oil physical characteristics

Test No.

Mg

Zn

Mo

Cu

Pb

Al

Ni

Cr

Fe

TBN

Viscosity

100 0C

Cts

397    29         1951      1423      3           2           10         <1          2           14         9.96       12.7                       640        35          1970      1579      8           10         9           <1         2           14         9.14       12.7                     

 

Conclusions:

  1. No wear detected within the period between the first test and the second test (1,250 hours).

 

  1. The characteristics of the oil changed very little within the period between the first test and the second test (1250 hours).

 

We have consistently received similar results on all the generators and decided to extend the oil change intervals 4 times (instead of every 250 hours to every 1,000, although the test results indicated that we could extend them to every 1,750 hours)."

 

(Note from the manufacturer: At the end of 2005 a diesel engine in which Bi-Tron had been used for almost 3 years, was taken apart. No traces of wear were found and the engine parts looked completely clean and almost new).

 

The following pictures are of engine parts of the above referenced generator when it was taken apart after 17,500 hours of operation (which is equivalent to 1 million km) with oil changes every 1,000 hours (versus every 250 hours without Bi-Tron).

 

Piston-rod-bearing housing is completely clean of any deposit build-up. The bearing itself is clean of any scoring or scuffing, has its original thickness and its surface looks highly polished.

 

Cylinder sleeve, completely clean with no deposit build-ups. In most of the sleeves, there were traces of cross honing of the original bore, meaning almost no wear took place. The sleeve walls were highly polished.

The piston-skirt and piston rings are completely clean of any deposit build-ups, and the piston ring-blades are highly polished (virtually no signs of wear). The build-up you see on the piston top, which is due to deposits from burnt fuel in combustion chamber, could be eliminated by using Bi-Tron Fuel Conditioner.

 

The oil baths, valve springs, valve stems and the block surface are completely clean of any deposit build-up.